Wiring LED Light Bar

Posted on: May 25, 2018, by :

Finding the Best LED Mini Light Bar

If you have no wiring harness, use a relay if your light bar draws over 5 amps. When directly switching a light bar, use a switch with a minimum 10A rating.

Finding the Best Off Road LED Light Bars

Prestige LUMAX Warrior Series 50 inch LED Light Bar Review

Black Oak LED 10 Inch D-Series Curved LED Light Bar Review

Try to keep wire lengths as short as possible. Route wires along firewalls or the vehicle chassis. Route wire away from high heat areas. Avoid splicing wire when possible. If you have a rooftop LED light bar, run the power wires through a windshield frame channel.

Best Black Oak LED Single Row LED Light Bar Reviews

Finding the Best LED Fog Light Bars

Fortunately, you already know how much current your LED light bar requires. So, you can easily choose the size of wire to feed it safely. Below is a list of automotive wire sizes and their safe current ratings.

Automotive relays are inexpensive and most handle 40A of current, which is more than enough for even large LED light bars. The relays are switched via a cab switch whose circuit carries less than 1A. Therefore, for a large light bar you can use a smaller cab switch and smaller wire on the switch circuit.

Rigid LED Light Bar Review: E-Series 40 inch LED Light Bar

Tip 3:It never hurts to choose one gauge larger, which means a lower AWG. This provides a greater margin of safety.

Rigid LED Light Bar Review: E-Series 30 inch LED Light Bar

Rigid LED Light Bar Review E Series

There are three grades of automotive wire: GPT, GXL and TXL. Your local auto parts will have GPT wire but probably not GXL or TXL grades. These grades have a higher temperature range and better resistance to solvents and other chemicals. If you can afford them, use them.

Good watertight connectors do not need a coating of silicone or electrical tape. If you are so compelled, however, use marine grade silicone and professional quality electrical tape.

Best Black Oak LED Curved LED Light Bar Reviews

Tip 7:Add a dual waterproof connector near the light bar for easy disconnection when the light needs to be removed.

Many people make the analogy that electrical current through a wire is like water through a hose. Unlike water hoses, however, pushing excessive electrical current through a wire that is too small will melt the insulation or cause a fire.

Black Oak LED 30 Inch S-Series LED Light Bar Review

Tip 1:Please do not skip over this section unless you have a great deal of experience with electrical wiring and components.

Once you have mechanically installed your new LED light bar, it is time to give it a steady supply of electrons so it has a steady supply of night vanquishing power. Learning how to wire and LED light bar correctly ensures reliability and avoids unsafe operating conditions or damage to your vehicle.

Finding the Best LED Strobe Light Bars

Feel free to view the collection of led light bars with detailed guides.

Best LED Light Bar Reviews Guide for 2016

The terminals have a standard numbering scheme. A fused wire runs between the positive battery terminal to relay terminal 30. Terminal 85 connects to a vehicle ground point. The load side of the cab switch goes to terminal 86. The positive wire from the light bar attaches to terminal 87 and the light bars negative wire attaches to a vehicle ground.

Black Oak LED 40 Inch S-Series LED Light Bar Review

Black Oak LED 10 Inch S-Series LED Light Bar Review

Your LED light bar probably has an IP67 or higher rating. Why compromise that with leaky connectors? Look for quality watertight wire connectors in a local marine store. When wiring LED light bar connectors, use crimpers that are specified for them.

The left column is the length of a wire, in feet. The top row is the number of amps applied to the wire. Choose a column that is equal to or greater than the maximum current draw of your light bar. The intersection between the selected row and column indicates the proper size of wire, in AWG or American Wire Gauge, you should use for the circuit.

Before you start, disconnect the vehicle battery. Do not take shortcuts. Disconnect it.

Finding the Best ATV LED Light Bars for Your Needs

This resource will help you find exactly what you need!

Rigid LED Light Bar Review: E-Series 38 inch LED Light Bar

Rigid LED Light Bar Review: E-Series 4 inch LED Light Bar

Prestige LUMAX Warrior Series 18 inch LED Light Bar Review

Federal Signal LED Light Bar Review

Tip 2:Always remove the ground terminal clamp first followed by removing the positive side clamp. This greatly reduces the risk of shorting the battery, which is both exciting and very dangerous. Removing the positive terminal first risks you or a tool coming into contact with any metal connected to the negative terminal, which is most of the car.

Rigid LED Light Bar Review: E-Series 6 inch LED Light Bar

Tip 4:When wiring LED light bar relays or switches, fuse all positive side wires such as from the positive battery terminal to the light bar switch. The fuse rating shouldnotcorrespond to the wire size but instead to the maximum current expected on that wire. In this case, that would be the light bars maximum current.

Rigid LED Light Bar Review: E-Series 10 inch LED Light Bar

Black Oak LED 20 Inch D-Series Curved LED Light Bar Review

Rigid LED Light Bar Review: E-Series 28 inch LED Light Bar

Rigid LED Light Bar Review: E-Series 50 inch LED Light Bar

Tip 8:Use separate wire colors for different circuits so they are easily identifiable. For instance, red for the wire from the battery to the relay, black for ground wires, yellow for a wire running from a relay to its switch, and so on.

Prestige LUMAX Warrior Series 28 inch LED Light Bar Review

Once yourLED light barhas been properly wired, you can drive with confidence knowing that your bright, night-splitting LEDs are getting all the power they can consume, reliably and safely.

Rigid LED Light Bar Review: E-Series 20 inch LED Light Bar

The diagram below shows the bottom side of a standard 12VDC automotive relay. Be sure the relay power capacity exceeds the amperage of your light bars maximum current draw.

Tip 5:Wrap electrical tape snugly over connectors without stretching or it will slowly unravel later.

A lot more can be said in regard to how to wire an LED light bar. However, the information in this guide should be enough for the handy person to complete the task. If you have doubts about your ability to deal with wiring, do not hesitate to employ an electrical specialist.

Your car or truck battery may appear dull and non-threatening, but it is a potentially life-threatening storehouse of electrons looking for any way out at the speed of light.

Unboxing Quality vs Cheap LED Light Bar overview

Watch this video on YouTubeConclusion

Tip 6:If your LED light bar came with a wiring harness and it includes a relay, use it, end of story.

Hey, Im Simon, thanks for visiting my website!

Prestige LUMAX Warrior Series 40 inch LED Light Bar Review

Finding the Best Emergency LED Light Bars

Leave a Reply