How to Wire Recessed Ceiling Lights

Posted on: May 21, 2018, by :

How to Wire Recessed Ceiling Lights

How to Wire Recessed Ceiling Lights

Get video instructions about kitchens, bathrooms, remodeling, flooring, painting and more.

Typically used for hallways and staircases, three-way switches are used in instances where two separate switches control one. Use these step-by-step instructions to install a three-way switch and wire a circuit.

How to Install a Light Fixture on a Stone Column Mailbox

At Disaster House, we invited heavy-metal rock band Slaughter to overload our electrical system. We had the band to hook up all of their electronics to a single 20-amp outlet just to see it blow.

Connect the wires and secure them with wire nuts (Image 2). Connect the three black (hot) power wires together, the three white (common or neutral) wires together, and the ground wires to each other. Also attach the ground wires to the boxs green ground screw, if provided, or to another metal connection in the box.

Attach the switch box to a wall stud. The typical height is 42 from the floor to the bottom of the box. If multiple switches are used, gang the boxes together. Follow electrical code recommendations as to the box area required for the number of switches installed.

Need some design inspiration? Sign up for the HGTV Inspiration newsletter today to get our tips and tricks!

The white wires do not connect to the switch. Twist them together and secure the splice with a wire nut.

For this installation, we are using 12-2 NM electrical cable. The 12 refers to the gauge, or thickness, of the individual wires, or conductors. The 2 indicates there are two insulated conductors (a bare or green-jacketed ground wire is also included). The NM stands for non-metallic, or plastic-jacketed, cable.

How to Replace a Light Fixture With a Ceiling Fan

How to Replace an Electrical Outlet Receptacle

Browse a full list of topics found on the site, from accessories to mudrooms to wreaths.

Use a wire stripper to remove about 1/2 of insulation from the ends of all the black and white wires. In addition to the incoming and outgoing wires, each box will contain one black and one white fixture wire.

Dont miss your favorite shows in real time online.

Recessed or can lights can be used as task lighting, accent lighting or to illuminate an entire room. Theyre easy to install into existing wiring and the best part, recessed light dont go out of style.

Install bulbs in all of the light fixtures, restore the power and test the operation of the switch and fixtures.

Save heating and cooling costs by replacing an existing light fixture with an energy-efficent fan/light combination.

We love to DIY. You love to DIY. Lets get together.

Replacing or upgrading a light switch is a simple and inexpensive DIY project.

Follow these steps to install a motion-activated light for added security around your homes exterior.

How to Clean a Barbeque Grill in 15 Minutes

How to Install Recessed-Panel Wainscoting

Pull the cable through the drilled holes, working from one end of the circuit to the other. When wiring a series of lights, run a single length of cable from one fixture location to the next, but leave plenty of excess wire to work with at each fixture.

When all of the fixtures have been wired, pull the cable from the first light fixture into the switch box and secure it with a box clamp. Pull the power wire from the main circuit into the box. (Make sure the power is shut off, and test the wires with a circuit tester to be safe.)

At each fixtures attached junction box, remove a knockout tab with a screwdriver (Image 1) for each of the incoming, and outgoing, cables and pull the cables into the box. Secure the cables with box clamps.

What Is the Ideal Height to Cut the Grass?

Solar-powered lights are a good option when theres no electrical source nearby.

nonmetallic building electrical wire

Connect the ground wires to each other and to the green ground screw on the switch.

Pull the Wire to the Fixture Locations

Sign up for weekly project ideas and advice from experts.

How to Build a Regulation Cornhole Set

How to Install a Three-Way Switch and Wire a Circuit

Adding a light to a mailbox gives it a sophisticated look.

Enter twice daily for your chance to win HGTV Smart Home 2018!

Use an auger bit or Forstner bit (Image 2) in a power drill to bore 1 holes for the wiring. A heavy duty right-angle drill makes it easier to work in tight spaces between the ceiling joists. This tool, called a Hole Hawg, is available at most rental centers.

Follow these simple steps whether you want to replace an indoor or outdoor sconce.

Follow the Rule of 8s — leave at least 8 of wire extending out past each junction box, use wire staples to attach the cable to the wood framing within 8 from the box, and fasten the cable within 8 from where it extends into the wall.

How to Install a Recessed Book Shelf

Strip the insulation from the wire ends and attach each of the black wires to a brass screw on the switch.

Refer to your wiring plan (Image 1) to determine the most efficient wiring route from fixture to fixture.

Learn how to replace a standard light switch with a dimmer switch.

Recessed high hat lighting or can lights provide excellent illumination and give a room an elegant appearance.

Wrap electrical tape around each of the wire nuts to ensure that the wire splices wont untwist.

Leave a Reply