How To Install LED Light BarPosted on: May 13, 2018, by : xnlamp
Tip: Use three drill bit sizes to make a single hole. Make a pilot hole with a small bit, say 3/32 inch. Enlarge the hole with a bit midway in size between the pilot bit and the final bit size. The last hole should be the exact size of the mounting bolts.
Rigid LED Light Bar Review: E-Series 20 inch LED Light Bar
Keep a plan on how to proceed clearly in your mind. Take everything one step at a time but think ahead to the next steps to avoid figuratively painting yourself into a corner. If you have doubts along the way, consult an expert especially with regard to circuit wiring.
Some LED light bar manufacturers or aftermarket suppliers make OE brackets to fit specific vehicles. These utilize existing body or chassis holes in your car or truck.
Tip: Be sure the rear of the light bar housing has good ventilation and is not near a heat source. LEDs must be cool to ensure proper operation and long life.
Use a wire gauge that matches or exceeds the maximum current of your LED light bar.
For light bar wiring, you need a pair of wire cutters, wire strippers and the correct crimpers for the connectors you choose. Use marine grade or IP-rated connectors and you can forgo tape and caulking to seal splices. Wire ties help route wiring under the hood and inside the cab.
Once you have completed the installation, enjoy your pride and joy as soon as possible. Have fun and be safe!
Best Black Oak LED CREE LED Light Bar Reviews
Rigid LED Light Bar Review: E-Series 38 inch LED Light Bar
Rigid LED Light Bar Review E Series
Fuse power wires to the expected current draw, not the wire size.
Rigid LED Light Bar Review: E-Series 50 inch LED Light Bar
Rigid LED Light Bar Review: E-Series 4 inch LED Light Bar
Some light bars have channel mounts. These allow flexibility with regard to positioning the mounting brackets, which slide into the housing channel. If you have a lumber rack or roll bar, specialized bar mounts and clamps may be the simplest way to get your LED light bar attached.
Hopefully, you already checked local and state regulations regarding the use of auxiliary lights on your vehicle. If not, do so now to avoid having to remove it or alter the mounting. For the largest light bars, you probably need a cover when not driving off-road.
Hey, Im Simon, thanks for visiting my website!
Finding the Best Emergency LED Light Bars
Prestige LUMAX Warrior Series 40 inch LED Light Bar Review
Best LED Light Bar Reviews Guide for 2016
Use waterproof wiring connectors. Check for these at a local marine shop.
Federal Signal LED Light Bar Review
Prestige LUMAX Warrior Series 28 inch LED Light Bar Review
Rigid LED Light Bar Review: E-Series 40 inch LED Light Bar
Use automotive grade wire. GPT is acceptable, but GTX and TLX grades are better.
Unboxing Quality vs Cheap LED Light Bar overview
Federal Signal LED Light Bar Review
Connect your light bar directly to the vehicle battery or another DC voltage source as soon as you open the box. If you use a power supply, make sure its voltage output is within the light bars specs. Also, make sure it can supply the maximum current your light bar draws.
If you already have a roll bar, then LED light mounting clamps are a great way to mount your lights, especially smaller ones. These also permit aiming the light in three dimensions. There are aftermarket light mounting bar kits available if you have no roll bar.
Always disconnect the negative terminal of your battery before starting the wiring.
Finding the Best Off Road LED Light Bars
Tip: When testing the light bar, do not look directly into the LEDs as the high-intensity light can damage your eyes.
Black Oak LED 10 Inch D-Series Curved LED Light Bar Review
To position end brackets properly, attach them to the housings end studs and with help from one or two assistants place the light bar in its final position. With free hands, you can make accurate marks through the holes of the bracket bases for drilling.
Black Oak LED 20 Inch D-Series Curved LED Light Bar Review
As long as you follow instructions and have basic tools, you can install your new LED light bar with little difficulty. This article provides basic installation guidance to supplement the directions or schematics that came with your light bar.
Do not place channel brackets more than one-quarter of the light bar length in from either end of the housing. If the mounting surface has areas that are reinforced, try to place the brackets on these to increase stability and reduce vibration.
This resource will help you find exactly what you need!
Besides a good set of screwdrivers, wrenches and pliers, you need a measuring tape and something to mark drill holes. Only use drill bits that are the right size and are sharp. Dull drill bits of the wrong size will create frustration for yourself and possibly damage your vehicle. Vise-locks or C-clamps can hold the light bar in position when marking holes.
Rigid LED Light Bar Review: E-Series 6 inch LED Light Bar
Before you jump into installing your new LED light bar, consider checking several things, before getting started:
Best Black Oak LED Single Row LED Light Bar Reviews
Best Black Oak LED Double Row LED Light Bar Reviews
Connect the light bars red wire to the positive side of the battery or power supply and the black wire to the negative terminal. If the light does not work, you need to take care of this problem before continuing with the installation.
Finding the Best LED Mini Light Bar
Black Oak LED 10 Inch S-Series LED Light Bar Review
Prestige LUMAX Warrior Series 18 inch LED Light Bar Review
Black Oak LED 30 Inch S-Series LED Light Bar Review
Tip: To ensure that mounting bolts or nuts do not loosen over time due to vibration, invest in a small tube of liquid thread locker.
Finding the Best LED Fog Light Bars
A more complete guide to LED light bar wiring ishere, but the general steps are these:
Rigid LED Light Bar Review: E-Series 28 inch LED Light Bar
With or without a relay, use a cab switch rated for at least 10 amps.
Rigid LED Light Bar Review: E-Series 30 inch LED Light Bar
Black Oak LED 40 Inch S-Series LED Light Bar Review
Use an automotive switching relay if the light bar draws 10A or greater.
Rigid LED Light Bar Review: E-Series 10 inch LED Light Bar
Smaller light bars are often mounted within the vehicle grill or under the bumper in the case of fog lamps. With only a stud to work with, you may have to fabricate a bracket to create a solid mount. Do not attach the stud to plastic parts even if they seem solid. Over time, vibration will crack the plastic around the hole.
Avoid unnecessary splices, but use a snap-in connector at the light bar to ease removal.
Prestige LUMAX Warrior Series 50 inch LED Light Bar Review
Finding the Best ATV LED Light Bars for Your Needs
Feel free to view the collection of led light bars with detailed guides.
Tip: Never connect your LED light bar to AC current as it will damage it.
Finding the Best LED Strobe Light Bars
Depending on the size ormanufacturerof your LED light bar, mounting brackets differ. Smaller light bars, around 4 to 12 inches, may have one or more threaded studs at the housing bottom. Longer light bars typically have studs on each end that fit into right-angle brackets held by screws or bolts attached to the vehicles body or chassis.
If you have researched variousLED light bar reviews, you probably noticed that a few buyers received opened packaging with parts missing. Make sure everything you expected to be in the box is actually there.