amp Cool Desk Lamp Made From Pipe

Posted on: May 5, 2018, by :

Thread another elbow onto the end of the ½-in x 6-in nipple. Pass the lamp wire through.

Thread a close nipple into the ¾ to 1 coupling,and fit the rubber bushing (white) and threaded rod (silver) from the lamp kit to the inside of the coupling.

This DIY lamp has an awesome, steam-punk style and can be put together in just a few minutes. You can find everything you need for this project at your local Home Depot store.

Connect the lamp wires to the socket.

Add an elbow and the ½ x 6 nipple to the top of the assembly.

3/4 in. x 1/2 in. Black Iron 90-Degree FPT x FPT Reducing Elbow – 100563923

You should always check with local authorities to ensure that any DIY project abides by local codes and regulations.

Then thread the ¾ to 1 coupling to the ½ to ¾ coupling.

This cool, easy-to-make pipe lamp will create a trendy look for your desk or table. Its made from lengths of steel pipe and fittings, a light kit and a light bulb all readily available at your local Home Depot store.

Thread two ½-in x 3-in nipples into a tee.

Thread the socket base onto the threaded rod in the assembly created in Step 9.

3/4 in. x 1/2 in. Black Iron 90-Degree FPT x FPT Reducing Elbow – 100563923

Electrified Candlestick and Bottle Adapter Kit – 204835997

Electrified Candlestick and Bottle Adapter Kit – 204835997

60-Watt Soft White ST19 Incandescent Original Vintage Style Light Bulb – 304685705

Electrified Candlestick and Bottle Adapter Kit – 204835997

© 2000-2018 Homer TLC, Inc. All Rights Reserved.

Screw in the light bulb, tighten the strain relief fitting on the back of the lamp. Switch your new industrial pipe lamp on!

3/4 in. x 1/2 in. Black Iron 90-Degree FPT x FPT Reducing Elbow – 100563923

Tell us a little bit about you and well find articles to fit your tastes. To start, just select some of the options below.

Electrified Candlestick and Bottle Adapter Kit – 204835997

Halloween Harvest Style Challenge

Pass the wire through the assembly created in Step 9, and thread it into the elbow.

60-Watt Soft White ST19 Incandescent Original Vintage Style Light Bulb – 304685705

Take a look at more DIY projects here on The Home Depot blog. And follow ourA Few of Our Favorite Thingsboard on Pinterest for more great DIY project ideas.

Electrified Candlestick and Bottle Adapter Kit – 204835997

Screw two ½-in x 3-in nipples into a tee for the middle bar. Thread the middle section into the legs created in Steps 2 and 3.

60-Watt Soft White ST19 Incandescent Original Vintage Style Light Bulb – 304685705

Fit the socket into the socket base.

Electrified Candlestick and Bottle Adapter Kit – 204835997

Repeat for the other leg of the lamp.

60-Watt Soft White ST19 Incandescent Original Vintage Style Light Bulb – 304685705

3/4 in. x 1/2 in. Black Iron 90-Degree FPT x FPT Reducing Elbow – 100563923

DIY Industrial Lamp: Cool Desk Lamp Made From Pipe

3/4 in. x 1/2 in. Black Iron 90-Degree FPT x FPT Reducing Elbow – 100563923

60-Watt Soft White ST19 Incandescent Original Vintage Style Light Bulb – 304685705

60-Watt Soft White ST19 Incandescent Original Vintage Style Light Bulb – 304685705

3/4 in. x 1/2 in. Black Iron 90-Degree FPT x FPT Reducing Elbow – 100563923

Thread a close nipple into the bottom of a tee. Then thread a strain relief fitting into the back of the tee.

Halloween Harvest Style Challenge

Thread the ½ x 10 nipple into the top of the tee. Thread the lamp wire through the strain relief fitting and up the neck of the 10-inch nipple.

Thread two elbows onto the exposed end of the ½-in x 3-in nipples. This will be one of the legs of the lamp.

Just follow the step-by-step tutorial, and youll have your new desk or table lamp completed in no time.

Use of this site is subject to certain Terms of Use which constitute a legal agreement between you and

Leave a Reply